|
|
You are here: Knowledge Base > Bradley Technical bulletins and Guides
|
Modesty Module Showers Models 4000 thru 4036 & Model 4044 Last Updated: 03/24/2008 |
||
|
Installation Instructions Step 1: Install floor anchors 1. Install your Bradley shower as instructed on the shower installation instructions provided with your new shower. 2. Check dimensions on the layout drawing (identified by a "MM" number) you received for correct location of pilasters, posts, and partitions. 3. Scribe lines on the floor to indicate the locations of the pilasters and posts in relation to the showers and/or walls according to the dimensions on the layout drawing you received. Step 2: Assemble pilaster and post support hardware 1. Using a pilaster floor bracket and a post foot angle as templates, locate and mark hole locations for the support hardware on the floor (refer to drawing received). NOTE: Alternate 4" and 6" pilasters as shown on page 3. The shower seat will be mounted to the partition attached to the 6" pilaster. 2. Drill floor holes for the pilasters and posts into the floor. NOTE: If you are drilling into concrete, drill 1/4" deeper than the length of the anchor. If you are drilling into a tile floor, make sure the top of the anchor is below the setting bed. 3. At each pilaster hole location, secure the hardware components shown in Figure 1. 4. At each post hole location, secure the hardware components as shown in Figure 2. Step 3: Install stirrups to hold partitions 1. Using a stirrup as a template, mark the locations for the stirrup screw holes on the pilasters and posts. Drill 5/32" diameter holes at the marks. 2. Fasten the stirrups, shown in Figure 3, to the posts and pilasters using the #10 x 1/2" sheet metal screws provided. 3. For column shower installations, fasten the stirrups shown in Figure 3 to the column shower's pre-drilled holes using the #10-24 x 1/2" self-tapping screws which are in a bag tied to the shower column. 4. For Modesty Modules fastened to the wall, mark stirrup locations and drill 3/8" diameter 1-1/8" deep holes in the wall. Install bracket to wall with lead anchors and 1/4" - 20 x 1-1/4" screws provided (see Figure 4). Step 4: Install pilasters and posts 1. Beginning with the first row of Modesty Modules™, slip shoes onto the bottom of posts (see Figure 5). 2. Set posts into position over the post foot angle and fasten mounting hardware (see Figure 5). NOTE: To allow for adjustments, DO NOT tighten screws until Step 5, Procedure 4. 3. Set pilasters into position over the floor bracket and install mounting hardware but do not tighten screws until Step 5, Procedure 4 (see Figure 6). 4. Assemble pilaster shoe around bottom of pilaster and install with #14 x 5/8" Phillip head screws provided (see Figure 6). NOTE: To allow for adjustments, do not tighten screws. Step 5: Install Modesty Module™ partitions 1. Using a support, set partitions on edge and slide into stirrups on posts and pilasters (and walls). 2. Position partition so the spaces on the sides of the partition are equal and the partition is level. 3. Make sure the partitions are level and plumb. For wall shower installations, install notched-out Wall-Saver first. For column shower installations, install partitions next to the column shower first. See Figure 7 for determining partition height. Then mark drill hole locations on partitions and drill 5/32" diameter holes in the partitions at the marked locations. 4. Make sure all parts are level and plumb. Fasten the partitions to the stirrups (and wall brackets) with #14 x 5/8" Phillips head screws (p/n 160-360) provided and secure posts and pilasters to floorbracket/foot angles. Step 6: Install head and curtain rails 1. Using a pilaster floor bracket and a post foot angle as templates, locate and mark hole locations for the support hardware on the floor (refer to drawingreceived). NOTE: Alternate 4" and 6" pilasters as shown on page 2. The shower seat will be mounted to the partition attached to the 6" pilaster. 1. Using the stirrup as a template, mark the screw hole locations on rails and drill 5/32" holes in marked locations. 2. Install aluminum head and curtain rails as shown in Figure 9. Make sure the headrails junction at the corners (see Figure 8). NOTE: Before fastening curtain rails, be sure to slide eight hooks per curtain (ten for extrastrength curtains) into position on the curtain rails. Step 7: Install shower seat 1. At the desired location, drill a 5/16" diameter floor hole for seat post. Mount the seat to a partition secured to a 6"pilaster. NOTE: Only one post per seat is provided and is to be centered under seat. 2. Assemble remaining seat post hardware as shown in Figure 10. NOTE: Do not put spacer under post foot angle. 3. Attach the two seat brackets included to the module partition (see Figure 11). Make sure seat brackets are level with bracket installed on seat post. NOTE: Two seat brackets are to be used for each seat. 4. For stainless steel seat mounting, drill two #9 (0.196" diameter) holes in the bottom of the seat using the bracket on seat post as a template. 5. Assemble seat to seat brackets and post bracket with screws provided (see Figure 11). Step 8: Complete Installation 1. Be sure that all hardware is mounted with proper number of screws and securely tightened. 2. Clean the stainless steel, partitions, seats, etc. before use (See page 2 for cleaning information). NOTE: If these instructions are followed, your Bradley Modesty Modules™ will provide years of dependable service. However, if these cleaning instructions are not followed, Bradley will not accept any responsibility for product failure. 3. Hang shower curtains on shower curtain hooks installed on curtain rails.
|